KWWidgets/Projects/3DWidgets/Part2/Study/Construction: Difference between revisions

From KitwarePublic
Jump to navigationJump to search
No edit summary
No edit summary
 
(2 intermediate revisions by the same user not shown)
Line 11: Line 11:
=== Widgets ===
=== Widgets ===
{|
{|


|-
|-
| valign="top"|
| valign="top"|
''' Measuring Angles '''
''' Compass Tool '''
| valign="top"|
| valign="top"|
CATIA's angle measurement widget two lines, a line and a curve, two curves, a curve and a surface, a line and a surface, a line and a plane, or two surfaces. It even permits the measurement of the complimentary angle between two curves.
The compass tool is situated in the top right of the main display.
It permits, by using the mouse, the user to rotate and/or translate the rendered scene. Rotations and translations are limited to the plane or axis selected by the mouse.
The compass tool can be dragged over any object in a scene and used to manipulate the targetted object.
| valign="top"|
| valign="top"|
[[Image:3DWidgets_Part2_Study_Construction_002.PNG|200px|Main screen of CATIA v5]]  
[[Image:3DWidgets_Part2_Study_Construction_004.PNG|200px|Compass tool]]  


|-
|-
| valign="top"|
| valign="top"|
''' Measuring Distances'''
''' Wireframes '''
| valign="top"|
| valign="top"|
Distances can be measured between points, lines, curves, surfaces, planes, edges and arc centres.
Enables creation of points, lines, planes and circles.
The tool also permits the measurement of minimum and maximum distances, to chain together a series of measurements or a fan of measurements.
Points my be created by co-ordinates, on a curve, on a plane, on a surface, at the centre of a circle or sphere, at a tangent on a curve or between other points.
Lines may be created from one point to another, from a point in a set direction, as an angle or a normal to a curve, as a tangent to a curve, as a normal to a surface or as a bisection of other lines/curves/etc.
Planes may be created as an offset from another plane, as parallel tthrough a point, as an angle or a normal to a plane, from three points, from two lines, from a point and a line, from a planar curve, as the normal to a curve, as a tangent to a surface, from an equation or as the mean through points.
Circles may be created from a centre point and a radius, from a centre and a point, two points and radius, three points, centre and axis, bitangent and point, bitangent and radius, tritangent or centre and tangent.
| valign="top"|
| valign="top"|
[[Image:3DWidgets_Part2_Study_Construction_001.PNG|200px|Main screen of CATIA v5]]


|-
|-
| valign="top"|
| valign="top"|
 
''' Measuring Angles '''
| valign="top"|
| valign="top"|
Different possible measurements include: distance, angle, complimentary angle, radius, diameter, centre point, centre of gravity, perimeter and area.
CATIA's angle measurement widget two lines, a line and a curve, two curves, a curve and a surface, a line and a surface, a line and a plane, or two surfaces. It even permits the measurement of the complimentary angle between two curves.
| valign="top"|
| valign="top"|
[[Image:3DWidgets_Part2_Study_Construction_003.PNG|200px|Main screen of CATIA v5]]  
[[Image:3DWidgets_Part2_Study_Construction_002.PNG|200px|Measuring angles]]  


|-
|-
| valign="top"|
| valign="top"|
''' Manipulators '''
''' Measuring Distances'''
| valign="top"|
| valign="top"|
 
Distances can be measured between points, lines, curves, surfaces, planes, edges and arc centres.
The tool also permits the measurement of minimum and maximum distances, to chain together a series of measurements or a fan of measurements.
| valign="top"|
| valign="top"|
[[Image:3DWidgets_Part2_Study_Construction_001.PNG|200px|Measuring distances]]


|-
|-
| valign="top"|
''' Rotation '''
| valign="top"|
| valign="top"|


| valign="top"|
| valign="top"|
 
Different possible measurements include: distance, angle, complimentary angle, radius, diameter, centre point, centre of gravity, perimeter and area.
|-
| valign="top"|
''' Dimension Manipulators '''
| valign="top"|
| valign="top"|
[[Image:3DWidgets_Part2_Study_Construction_003.PNG|200px|Measuring distances]]


| valign="top"|


|-
|-
| valign="top"|
| valign="top"|
''' Tools '''
''' Manipulators '''
| valign="top"|
| valign="top"|
 
Manipulators provide the user with the ability to perform certain interactions with objects.
Using CATIA's FreeStyle set, a manipulator can be used, constrained to either a line or a plane. Using such a tool, one surface can be manipulated to form a projection onto another surface, or multiple points can be used in order to match two surfaces.
The direction of manipulation is constrained by use of the compass tool.
| valign="top"|
| valign="top"|


|-
|-
| valign="top"|
| valign="top"|
''' Reference Elements  '''
''' Blend Tool '''
| valign="top"|
The Freeform Blend Surface tool enables the user to create a third surface that blends the together two separate surfaces.
| valign="top"|
| valign="top"|


| valign="top"|


|-
|-
Line 78: Line 80:
''' Boolean Operators '''
''' Boolean Operators '''
| valign="top"|
| valign="top"|
 
Tools for assembling, adding, removing, intersecting, and trimming bodies, also for keeping and removing object faces.
| valign="top"|
| valign="top"|


Line 86: Line 88:
''' Transformation Features '''
''' Transformation Features '''
| valign="top"|
| valign="top"|
 
Permits transformations of an object such as rotations, symmetry, mirror, patterns and scales.
| valign="top"|
| valign="top"|


Line 93: Line 95:
''' Draft Analysis '''
''' Draft Analysis '''
| valign="top"|
| valign="top"|
 
Performs an analysis of a draft angle on an object to see whether the piece may be easily removed.
| valign="top"|
| valign="top"|


Line 100: Line 102:
''' Structural Analysis'''
''' Structural Analysis'''
| valign="top"|
| valign="top"|
 
Performs first-order structural analyses:
* ''Generative Part Structural Analysis'' simple interface, permits user to obtain mechanical behavior information.
* ''ELFINI Structural Analysis'' extensive mechanical analysis.
* ''Generative Assembly Structural Analysis'' mechanical analysis of an entire body.
* ''Generative Dynamic Analysis'' dynamic response analysis.
| valign="top"|
| valign="top"|




|}
|}

Latest revision as of 08:05, 9 November 2006

CATIA v5

Main screen of CATIA v5

CATIA v5 is produced by IBM: [1]


CATIA V5 is the leading product development solution for all manufacturing organizations, from OEMs through their supply chains to small independent producers. The range of its capabilities allows CATIA V5 to be applied in a wide variety of industries, such as aerospace, automotive, industrial machinery, electrical, electronics, shipbuilding, plant design, and consumer goods, including design for such diverse products as jewelry and clothing.
CATIA V5 is the only solution capable of addressing the complete product development process, from product concept specifications through product-in-service, in a fully integrated and associative manner. It facilitates true collaborative engineering across the multi-disciplinary extended enterprise, including style and form design, mechanical design and equipment and systems engineering, managing digital mock-up, machining, analysis, and simulation. Extract from IBM website linked above

Widgets

Compass Tool

The compass tool is situated in the top right of the main display. It permits, by using the mouse, the user to rotate and/or translate the rendered scene. Rotations and translations are limited to the plane or axis selected by the mouse. The compass tool can be dragged over any object in a scene and used to manipulate the targetted object.

Compass tool

Wireframes

Enables creation of points, lines, planes and circles. Points my be created by co-ordinates, on a curve, on a plane, on a surface, at the centre of a circle or sphere, at a tangent on a curve or between other points. Lines may be created from one point to another, from a point in a set direction, as an angle or a normal to a curve, as a tangent to a curve, as a normal to a surface or as a bisection of other lines/curves/etc. Planes may be created as an offset from another plane, as parallel tthrough a point, as an angle or a normal to a plane, from three points, from two lines, from a point and a line, from a planar curve, as the normal to a curve, as a tangent to a surface, from an equation or as the mean through points. Circles may be created from a centre point and a radius, from a centre and a point, two points and radius, three points, centre and axis, bitangent and point, bitangent and radius, tritangent or centre and tangent.

Measuring Angles

CATIA's angle measurement widget two lines, a line and a curve, two curves, a curve and a surface, a line and a surface, a line and a plane, or two surfaces. It even permits the measurement of the complimentary angle between two curves.

Measuring angles

Measuring Distances

Distances can be measured between points, lines, curves, surfaces, planes, edges and arc centres. The tool also permits the measurement of minimum and maximum distances, to chain together a series of measurements or a fan of measurements.

Measuring distances

Different possible measurements include: distance, angle, complimentary angle, radius, diameter, centre point, centre of gravity, perimeter and area.

Measuring distances


Manipulators

Manipulators provide the user with the ability to perform certain interactions with objects. Using CATIA's FreeStyle set, a manipulator can be used, constrained to either a line or a plane. Using such a tool, one surface can be manipulated to form a projection onto another surface, or multiple points can be used in order to match two surfaces. The direction of manipulation is constrained by use of the compass tool.

Blend Tool

The Freeform Blend Surface tool enables the user to create a third surface that blends the together two separate surfaces.


Boolean Operators

Tools for assembling, adding, removing, intersecting, and trimming bodies, also for keeping and removing object faces.


Transformation Features

Permits transformations of an object such as rotations, symmetry, mirror, patterns and scales.

Draft Analysis

Performs an analysis of a draft angle on an object to see whether the piece may be easily removed.

Structural Analysis

Performs first-order structural analyses:

  • Generative Part Structural Analysis simple interface, permits user to obtain mechanical behavior information.
  • ELFINI Structural Analysis extensive mechanical analysis.
  • Generative Assembly Structural Analysis mechanical analysis of an entire body.
  • Generative Dynamic Analysis dynamic response analysis.