[ITK] ITK Toolkit?

[Tünde Szilágyi]

I apologize now I have attached the screenshot.

On 18 November 2015 at 08:30, Tünde Szilágyi <a.tunde.szilagyi at gmail.com>
wrote:

> Thank you, I have made the new selection to VS 14 2015 Win64 generator in
> CMake.
>
> However, the patch that solved the error messages is:
>
> http://review.source.kitware.com/#/c/20272/
>
> and NOT:
>
> http://review.source.kitware.com/#/c/20154/1
>
> I have now no errors during CMake configuration/generation step. The VS 14
> 2015 build is successful with 335 succeeded, 0 failed, 0 updated.
>
> BUT the ~/ITK_bin/bin/Debug/  does not contain the expected
> directories/files. By expected I mean the ones specified in the
> ITK_Tutorial:
>
> ITKCommon
> ITKBasicFilters
> ITKAlgorithms
> ITKNumerics
> ITKFEM
> ITKIO
> ITKStatistics
> ITKMetalIO
> itkpng
> itkzlib
>
> I have attached the CMakeCache.txt and the selection in the configuration
> stage in CMake.
>
> Many thanks in advance.
>
>
> On 18 November 2015 at 04:40, Dženan Zukić <dzenanz at gmail.com> wrote:
>
>> What I meant is that the choice of generator should include Win64 in its
>> name, as shown in the attached screenshot. CMake executable is Win32, that
>> does not matter. Also, I just built ITK in 32 bit mode without issues, so
>> something else is amiss.
>>
>> Can you attach your CMakeCache.txt?
>>
>> On Tue, Nov 17, 2015 at 8:12 PM, Tünde Szilágyi <
>> a.tunde.szilagyi at gmail.com> wrote:
>>
>>> I have tried without the patch, but I am receiving the same error
>>> message. My generator is VS 14 2015 (see CMake window on the LHS).
>>>
>>> Now, I have cleaned everything and started with a fresh installation:
>>> - Git Bash
>>> - CMake
>>> - ITK master
>>>
>>> I realized that only Win32 CMake exists on the official website:
>>> https://cmake.org/download/
>>>
>>> Is this what you refer to in your e-mail below? What else would you
>>> recommend?
>>>
>>> Many thanks.
>>>
>>>
>>> On 18 November 2015 at 01:34, Dženan Zukić <dzenanz at gmail.com> wrote:
>>>
>>>> That patch was merged to master, so you don't need to apply it.
>>>>
>>>> I used VS2015 *Win64* as the generator. You seem to be using *Win32*,
>>>> that might make a difference.
>>>>
>>>> I used version 3.3.1, which I installed some time ago. You are using
>>>> release candidate version - I doubt that is the reason.
>>>>
>>>> Can you try a clean clone (git clone git://itk.org/ITK.git), and then
>>>> building into a clean directory?
>>>>
>>>> On Tue, Nov 17, 2015 at 7:19 PM, Tünde Szilágyi <
>>>> a.tunde.szilagyi at gmail.com> wrote:
>>>>
>>>>> During CMake I am getting the attached error message. All the error
>>>>> messages I receive is with reference to exe files starting with
>>>>> cmTC_XXXXXX.exe. I have used the patch from Matt from September 1 to solve
>>>>> this (http://review.source.kitware.com/#/c/20154/1 - Checkout), but
>>>>> this still results in the same error messages as before. I have attached
>>>>> one of the error messages that appear during CMake project configuration.
>>>>>
>>>>> Many thanks.
>>>>>
>>>>> On 18 November 2015 at 00:41, Dženan Zukić <dzenanz at gmail.com> wrote:
>>>>>
>>>>>> Master branch from git://itk.org/ITK.git
>>>>>>
>>>>>> On Tue, Nov 17, 2015 at 6:34 PM, Tünde Szilágyi <
>>>>>> a.tunde.szilagyi at gmail.com> wrote:
>>>>>>
>>>>>>> Which ITK version did you use?
>>>>>>>
>>>>>>> On 18 November 2015 at 00:14, Dženan Zukić <dzenanz at gmail.com>
>>>>>>> wrote:
>>>>>>>
>>>>>>>> This configuration compiles fine in debug too.
>>>>>>>>
>>>>>>>> On Tue, Nov 17, 2015 at 5:45 PM, Dženan Zukić <dzenanz at gmail.com>
>>>>>>>> wrote:
>>>>>>>>
>>>>>>>>> Hi Tünde,
>>>>>>>>>
>>>>>>>>> checking out *master* branch and CMake configuration went fine.
>>>>>>>>> To speed up compile time, I disabled building of examples and testing. I
>>>>>>>>> also enabled ITK_LEGACY_REMOVE. I did not enable Module_ITKVtkGlue.
>>>>>>>>>
>>>>>>>>> Opening the solution file in VS2015 was fairly slow - it might
>>>>>>>>> have something to do with the fact I just installed it. Building in Release
>>>>>>>>> x64 finished without a problem: 212 succeeded, 0 failed, 3 skipped.
>>>>>>>>>
>>>>>>>>> Regards,
>>>>>>>>> Dženan
>>>>>>>>>
>>>>>>>>> On Tue, Nov 17, 2015 at 5:14 AM, Tünde Szilágyi <
>>>>>>>>> a.tunde.szilagyi at gmail.com> wrote:
>>>>>>>>>
>>>>>>>>>> Hi Everyone,
>>>>>>>>>>
>>>>>>>>>> I would be interested whether anyone has managed to build the ITK
>>>>>>>>>> Toolkit on Windows 10 64 bit with Microsoft VS 14 2015?
>>>>>>>>>>
>>>>>>>>>> Many thanks.
>>>>>>>>>> Tunde
>>>>>>>>>>
>>>>>>>>>> _______________________________________________
>>>>>>>>>> Community mailing list
>>>>>>>>>> Community at itk.org
>>>>>>>>>> http://public.kitware.com/mailman/listinfo/community
>>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> --
>>>>>>> --
>>>>>>> Tunde
>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>> --
>>>>> --
>>>>> Tunde
>>>>>
>>>>
>>>>
>>>
>>>
>>> --
>>> --
>>> Tunde
>>>
>>
>>
>
>
> --
> --
> Tunde
>



-- 
--
Tunde
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://public.kitware.com/pipermail/community/attachments/20151118/7960e786/attachment-0001.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: T2_step_2.png
Type: image/png
Size: 1072728 bytes
Desc: not available
URL: <http://public.kitware.com/pipermail/community/attachments/20151118/7960e786/attachment-0001.png>